EEPower

Recom Adds Full-Bridge Transformer Driver for 1 W to 20 W Supplies


New Products 6 hours ago by Luke James

Recom Power has added the RVP007, an integrated transformer driver for building isolated DC-DC supplies with outputs between 1 W and 20 W. The device integrates four power MOSFETs in a full-bridge configuration, accepts an input of 4.5 V to 24 V, and can run in resonant LLC mode, which the Austrian company says reduces electromagnetic interference and improves efficiency.

The RVP007 sits above Recom’s existing push-pull drivers, such as the RVP6501, in both input range and power. Those parts are limited to inputs of 2.8 V to 6 V and current limits below 1 A, which caps them at a few watts. The full-bridge topology and higher voltage rating of the RVP007 extend the same build-your-own approach to 12 V and 24 V industrial rails.

 

RVP007 series.

RVP007 series. Image used courtesy of Recom
 

Full Bridge in an 8-Pin Package

A full bridge drives the transformer primary with the full input voltage in both polarities, using the core more effectively than a push-pull stage and eliminating the center-tapped primary. The trade-off is four switches instead of two, and the RVP007 absorbs all four into a 5 mm by 6.2 mm ESOP-8 package 1.65 mm high.

According to Recom product information, the n-channel devices have an on-resistance of 0.15 ohms and the p-channel devices 0.30 ohms, with a 2.2 A current clamp and tolerance for input surges up to 38 V.

The transformer turns ratio and secondary-side rectification set the output voltage, so a single driver can produce anything from a 5 V logic rail to the bipolar 15 V/-8 V supplies that SiC and IGBT gate drivers need.

Meanwhile, the CLK pin programs the switching frequency. Left open, the internal oscillator runs at a nominal 250 kHz; an external resistor adjusts it anywhere from 75 kHz to 750 kHz. Lower frequencies suit larger transformers at the 20 W end of the range, and higher frequencies allow smaller magnetics in the low-watt designs.

Integrated soft start limits inrush at power-up, and built-in dead-time control keeps opposing switches in each leg from conducting at the same time. Protection covers input overvoltage, current limiting, continuous short-circuit operation, and overtemperature with automatic recovery.

 

LLC Mode for EMI and Efficiency

The option to run the bridge as an LLC resonant converter is what distinguishes the RVP007 from a basic hard-switched driver. In an LLC stage, the transformer’s leakage and magnetizing inductances form a resonant tank with a series capacitor, and the bridge switches at or near the tank’s resonant frequency.

 

Full-bridge and LLC topology.

Full-bridge and LLC topology. Image used courtesy of Recom
 

The primary current becomes approximately sinusoidal rather than trapezoidal, and the MOSFETs turn on at zero voltage. That lowers switching losses, which is where the efficiency gain comes from, and it softens the voltage and current edges that generate conducted and radiated EMI.

The programmable clock is an important inclusion here, because an LLC stage behaves as intended only when the switching frequency matches the resonant frequency of the chosen transformer and capacitor. The 75 kHz to 750 kHz range gives designers room to tune the tank for a given magnetic rather than designing the magnetic around a fixed oscillator. Recom hasn’t published efficiency curves for either mode, however.

 

A Discrete Alternative to Modules

Recom built its name on encapsulated DC-DC modules, and the RVP007 extends a discrete portfolio the company has been assembling for designs that need control over the magnetics or an unusual output. That portfolio includes the RVP family of flyback, push-pull, and full-bridge drivers, the RVS002 full-bridge rectifier IC and RVSY018 synchronous rectification controller, and the RMR and RBE families of SMD transformers rated from 1 W to 30 W with isolation up to 5 kVAC.

The RVP007 offers engineers an integrated full-bridge solution for compact isolated supplies. The company lists gate-driver supplies for IGBT and SiC switches, industrial control, including DCS and PLC equipment, UPS systems, photovoltaic inverters, telecom and radio equipment, precision instruments, and medical devices as target applications.